HEIGHTS ACCESSORIES for your tower:

Accessories that go on or near the tower top --

Top Shelves -- A flat, top plate for your top tower section, pre-drilled for whatever thrust bearing type you have.  This arrangement is great for antenna arrays that need to be rotated.

Designation

Weight(lbs.)

Price

TS11-100

4

$65

TS11-131

4

$69

TS14-100

5

$70

TS14-131

5

$72

TS18-131

6

$84

TS18-172

6.5

$89
TS22-172

7

$89
TS26-225

12

$129

 

 

 Top Shelf mounted on Crank Up, Telescoping tower.  Drilled for later mounting of thrust bearing.

Rotor Shelves -- flat plate to mount an antenna rotator, pre-drilled for whatever rotator type you have.   "RS"s for stacked towers include stainless U-bolts.  If you need an "RS" for a crank-up telescoping tower, be sure to specify "RS-CUA" as this is a different RS design.

Designation

Weight(lbs.)

Price

RS11-100

4

$64

RS14-100

4.5

$69

RS14-131

5

$72

RS18-131

6

$84

RS18-172

7

$89

RS22-172

9

$106
RS26-172/225 14

$129

 

"In-line" Rotor Shelf

("RS-CUA") for

Telescoping Tower.

 

Typical Rotor Shelf

for Stacked tower

design,  fastened

with heavy-duty

stainless U-bolts.

 

THRUST BEARINGS -- corrosion resistant, enclosed units for the HAM operator

DESCRIPTION

PRICE

TB UNIT A -- up to 2" O.D. mast capacity with 4 set bolts and mast protector shims

$37

TB UNIT B -- up to 2.66" O.D. mast capacity w/ 8 set bolts and mast protector shims

$54

TB-'A'

TB-'B'

 

HI-TENSILE ALUMINUM MASTS -- high quality, certified 6061T6 alloy mast tubing at low prices.  Most masts can be cut for $5 per cut.  Additional sizes available--just ask.  These are not cheap alloy tubes:  read  "6061 T6 extruded"; no one beats our values.  If you can find a better deal, let us know.  Note to Heights customers selecting mast:  We strongly recommend and often prohibit using a mast other than an aluminum one for your complete Heights Tower Kit.  These listed masts are more than strong enough to handle just about any application and will put less dead weight on the top of the towers, which can effect the operation and final load capacity of the towers.  Keep your whole tower ensemble in aluminum from the start--it's the smart thing to do.  You can't 'trick-load' and pump up any tower's real final windload by pimping a heavy, exotic, hardened material on top.  The whole design ensemble must match!

Outside Diameter (inches)

Inner Diameter--working*

Wall Thickness (inches)

Lengths (ft.)

Weight (lbs.)

PRICE

1.90"

 1.50"

0.20"

20' / 10'

25.12 / 12.56

$112 / $59
1.90" 1.61" 0.145" 20'/10'

18.8 / 9.9

$103 / $54

2.0"

 1.75"

0.125"

 24' / 12'   

21.26 / 10.63

$69 / $38

2.0"

 1.50"

0.250"

24' / 12'

38.8 / 19.44

$155 / $79
2.0" 1.312" 0.344" 20'

47

$139.00

2.375

 2.067"

0.154"

20'

25.2

$104.00

2.0"

 --

solid bar

 12'

44.34

$145.00

2.25"

 1.75"

0.250"

24' / 12'

49.92 / 24.96

$198/$102

2.25"

 1.75"

0.250"

8'

14.78

$66.00

2.875"

 2.323"

0.276"

20'

55

$161.00

1.72"

 1.334"

0.193"

8'

8.66

$41.00

1.312"

 1.032"

0.140"

8'

4.65

$29.00

1.0"

 0.75"

0.125"

8'

3.23

$24.90

*An Outer Diameter tube must be at least 0.015" smaller than the Inner Diameter of the tube you want to slip it in, to fit without force pressing.

COMPARE THESE PRICES TO ANY OTHER VENDOR ANYWHERE!  WE BEAT ANY DEAL ON OUR HIGH QUALITY, STRUCTURAL EXTRUDED TUBING (6061 T6 Alloy).  We buy in volume for our factory production, so YOU can save$$!   All lengths over 9 ft. in length must be shipped via motor freight,usually incurring a $75 minimum charge.  Residential deliveries are usually about $45 additional to that base charge.    Tubes are wrapped in cardboard, prepared for shipment!

ANTENNA STAND-OFF ARMS -- Two-tiered extension arms to mount your antennas 3 ft. away from the edge of the tower.  Great for adding extra antenna mounting capacity to stacked tapered towers, these aluminum arms are clamped to the tower with stainless U-Bolts and their antenna mount end has large 2" diameter capacity U-bolts to accept your antenna post or a 2" Dia. mast. . . $109 without mast;  $132 with 42" mast.  (Specify section-tube leg size when ordering).  Double Antenna Stand-Off is $207 with two 3.5 ft. masts.  Available in all sizes, for mounting on any tower section.  Typical extension is 3 ft.

Above:  Double Antenna Stand-Off for 22" section, with 52" and 14" side extensions, and large 3 ft. height.

Right:  Single Antenna Stand-Off for Top Section, with 36" extension off to side, 2 ft. height, and 6 ft. mast.

CO-AXIAL CABLE STAND-OFF ARMS -- 2 ft. extension arms to keep your coax away from the tower.  Great for crank-ups, these arms are clamped to the tower with a stainless U-Bolt and the other end has large 2"+ dia. loop tongs to allow for convenient insertion of various sized coax cables . . . $38 per unit.  (Specify section-tube leg size when ordering.) 

GIN-POLE KITS --  a great tool for stacked towers in hard to reach locations such as wooded areas, etc., or for towers not mounted on our convenient Fold-Over-Kits.  The Gin-Pole gives you the ability to erect your tower from the ground straight upwards, without the help of a crane. 

Ginpole.jpg (64948 bytes)

Gin-Poles are constructed of steel.  Sheave for the Head is for use with up to 1/4" cable or 5/16" rope.  (Rope/cable not included).   Clamp is about 11" in length, and adjusts to various size legs between 1" to 3" diameters.  Kits with and without Poles ARE UPS shippable!

Clamp & Head shown on tall pole next to section.  Demo'd by Jay C.

Close-up of easily adjustable Clamp.

 

GP288 Clamp and Head

$199

14.6 lbs.

GP288 Clamp, Head & Pole (2" Dia. x .25" wall x 8'10" length for UPS shipment)

$252

29.5 lbs.

Mast Raising Fixture - - a special sheave housing bolted to your Top Plate, with a winch and 20 ft. stainless cable to attach to mast.  This device allows for easy raising and lowering of your mast array-- handy for use with a double thrust-bearing system . . . $235.00, approx. 18 lbs.

Mrf.jpg (52868 bytes)

Mast Raising Fixture on Crank-Up tower.

Pulleys - -  We have pulley sheaves of stainless, aluminum and steel material, with and without bronze bushings; we also have aluminum Roller Spools.   Diameters run between 1.75" and 4.5".  Call factory for prices, including some special clear-outs.

Sheaves.jpg (18160 bytes)

Here are a few examples.  If you need custom pulleys, be prepared to forward drawing for quotation.

Grounding Kits -- Heights' approved grounding kits to provide appropriate grounding of tower legs to earth.  Jumbo stainless or aluminum strap clamps to tower legs and copper clamps to ground rods; wire cable for star loop and rods included.  Quality materials (not sold seperately).
Stand Leg with freshly installed Grounding Kit, including heavy copper strands to driven rod, and clamps on leg.  Wire on ground encircles tower base (25 ft. perimeter).

 
Tower's Less than 48 ft. -- two leg ground contact $174.00
Tower's from 48 to 120 ft. -- three leg ground contact $245.00

 

 Lightning Rod Tips-- aluminum tower rod and mount for top of mast (2" O.D. or less), to extend the highest point on tower and create an air terminal.  Normal length is 30", but may be extended.  Regular size  . . . . . . $39.00

 
 OBSTRUCTION LIGHTS, LED--  extremely long lasting, 10 to 20 year life-span.  360° visibility in flat plane.  Standard light color is red, but other colors available on special order.  Steady burning, but customer may add own flash controls.    Available in 115 Volt AC,12 or 24V DC, or other options.   Awesome introductory price ......Only   $289.00!!!   (Includes vertically centering mast mount, for up to 2" Diameter.  Special mounts available on request.   5 year warranty.  
             

Blinking  (Strobe) version of Obstruction Light, LED--  $398.   Timed versions, including darkness-actuated available also.  Please inquire with your specs for price and availability.  5 year warranty.  No one beats our values.

 

 

 

 
Copyright © 1998-2007 Heights Tower Systems